All I did to program a TV was: 1) Press TV on remote 2) Make sure tv is off 3) Press and hold the CODE SEARCH button till the LED is solid 4) Press CH^ until the tv turns on 5) Press enter Time may very depending on tv, make sure your figure is loose and can tap a button for a good period of time
First, make sure the device you want to connect with your remote is turned on, whether that’s the television, DVD player, VCR player, etc. Now aim the Innovage remote at the device. Press the button on the remote control that corresponds to the device (TV, DVD, etc.). Now, press and hold the SET button on the remote control until the LED light on the remote control holds a steady red. Enter the 4-digit code for your device by pressing the number keys on the remote control (see list below). When you press the fourth digit, the LED light should turn off. This means the remote and the device are "speaking" to each other. Press the OK button to store the code. If the LED light blinks three times and then remains a solid red, the Innovage remote doesn’t recognize the code for your device. Verify the correct code, then go through the programming steps again. Test the function by using your remote to cycle through all programmed devices (TV, VCR, etc.). If your device code isn’t listed, try the Code Search function: Turn on the device you wish to match with your remote. Aim the remote at the device and press and hold the Code Search button in the upper left of your remote for at least 3 seconds until the LED light on the remote turns a solid red. Press the button on the remote for the item you want to program (TV, DVD, etc.). The LED light should blink once and then remain a solid red. Press the On/Off button slowly until the device you want to program turns off. The LED light will blink once each time you depress the On/Off button. When the device you want to program turns off, press the ENTER button. The LED button will turn off and the code for that device will be stored in your remote. The codes to various devices are listed at:www.remotecentral.com Please note that there are often several codes for one particular device. It may take several programming attempts until you find the code that works with your device.
First turn on device.(TV, DVD,VCR,SAT) Point remote at device. Press "Code Search". Hold button for 3 Seconds until red LED Lights up solid red. Press button of which device you wish to program. Red LED will blink one time and remain solid red. Enter 3 Digit code from code list. If red LEd turns off the code is compatible with device. If it doesn't turn off, try the next 3 digit code. When LED turns off, press the ON/OFF button. If device powers off, you have the right code. Make a note of code for future reference.
Hold down code search until red light stays on then press the corresponding button to go with what your programming (TV DVD etc) then slowly press power repeatedly until device turns off but don't press the power button any extra times it will do the wrong code but once your tv turns off then press enter and your done WORKS ALMOST EVERYTIME!
THIS WORKS! First you push the button for witch device you want to program for example TV then press and hold code search until the light stays on then hit TV again. Point the remote at the tv and press repeatedly about once every second until the power goes off then press enter
Start by turning on the device that you want to program. (1) Press & release the device button that you want to program, lets say "VCR" LED will flase once (2) Press & hold the "CODE SEARCH" button until the LED stays on. (3) Press and release the POWER button. Point the remote at the device. (4)The LED will flash as the remote is searching for the code. (5) As soon as the device turns off press and release the "ENTER" button. The remote should NOW be programed.
Turn on device that you want to set Aim remote at the device Press the device button for the item you wish to program and the LED will blink once Press and hold the set button unti the LED lights up solid red Using the number keys, enter the 4 digit code from the list. After you have entered the 4th digit, the LED will turn off, indicating that the code for the device was recognized. If the device powers off, test the functions for the other buttons (except OK button). If all the functions work, press the OK button to store the code. If the indicator light remains solid red after blinking 3 times the code is incompatable. You then need to restart back on step 2. Make a note of the correct 4 digit code for future use.
COde search setting is an alternative method to programming your device without using the code list Turn on the device you want to set Aim the remote control at the device Press the decive button for the item you want to program Press and hold the SET button until the LED light up solid red Press the MUTE/SEARCH button. The LED will shut off first then light up solid red. When the device turns off, press the OK button to store this code.
Code Retrieval Press and hold the device button you want to display on the remote control Press the NUMBER 1 then count the number of flashes Press the NUMBER 2 etc Press the NUMBER 3 ets Press the NUMBER 4 etc
I have a jumbo universal remote and I have a Sylvania TV.... I have tried the code search process as well as using the remote to turn the tv on/off by pressing tv, then code search then on/of repeatedly.....Now my problem is after I get the tv to turn off using the remote, I would press enter then nothing happens. The tv doesn't turn back on or anything...So what's the next step from there?
Turn on the device that you want to be programmed. Hold code search button till red light stays on. Press which device you want programmed. Point directly at it and hit the on/off button repeatedly. Should turn off device, then hit enter.
